山碩UPS儲能動力專用磷酸鐵鋰電池芯32700及PACK組裝定做
價格
訂貨量(只)
¥15.00
≥1
店鋪主推品 熱銷潛力款
䝒䝕䝓䝒䝕䝑䝕䝐䝒䝐䝏
在線客服
UPS儲能動力專用磷酸鐵鋰電池芯32700廠家批發及PACK組裝定做
產品型號
型號:SSP-32700-6000mAh
Model:SSP-32700-6000mAh
引用標準
本標準參考國標GB/T18287-2013、UL1642 、IEC62133 UN38.3以及CE61960等技術標準規范編制而成。
產品規格
項目Items | 規格Specification | 備注Remarks | |
4.1 標稱容量Nominal Capacity | 6000mAh | 0.2 C放電 | |
4.2 標稱電壓 Nominal Voltage | 3.2V | Work voltage工作電壓 | |
4.3 放電終止電壓Discharge Cut-off Voltage | 2.0V | 0.2 C放電 | |
4.4 充電限制電壓Charge Limited Voltage | 3.65±0.03V | 0℃~45℃ | |
4.5 標準充電電流Standard Charge Current | 0.2 C | 0℃~45℃ | |
4.6 標準放電電流Standard Discharge Current | 0.2 C | -10℃~60℃ | |
4.7 快速充電電流Rapid Charge Current | 0.5C | 0℃~45℃ | |
4.8 快速放電電流Rapid Discharge Current | 0.5C | -10℃~60℃ | |
4.9 最大放電電流Max. Discharge Current | 3C | 終止電壓2.0V | |
4.10最大脈沖放電電流 (瞬時 ms) (Max. Pulse Discharge Current) | 5C | 瞬時 ms | |
4.11 內阻Internal Impedance | ≤20mΩ | AC 1kHz條件下At AC 1kHz | |
4.12 重量Weight | 大約About 140.0g | 重量±3g | |
4.13 電池儲存環境溫度范圍 Storage Temperature Range | ≤1個月one month | -20℃ ~ 45℃ | 出貨電壓 (Voltage of shipment) >3.32V |
≤3個月three months | -20℃ ~ 35℃ | ||
≤12個月a year | -20℃ ~ 25℃ |
電池外形結構及尺寸
安全性能
項 目Items | 測試方法Test Conditions | 標 準Specification |
7.1 外部短路 (Short Circuit) | 分別在 20±5℃和 55±5℃的環境溫度下依次用內阻為 80±20m? 的銅線連接電池芯的正負極持續放電直至發生爆炸、起火或至電壓小于 0.2V,電池芯表面溫度回復到環境溫度±10℃以內。電池芯要求:充滿電的新電池芯。 (Each test sample cell is to be short-circuited by connecting the positive and negative terminals of the cell with a Cu wire having a maximum resistance load of 80±20m?. The sample is to discharge until a fire or exposition is obtained, or until it has reached a completely discharge state of less than 0.2V and the sample case temperature has returned to ±10 of the ambient temperature. Tests are to ℃ be conducted at 20±5℃ and 55±5℃. Cell Condition: Fresh, Fully charged cell.) | 電池應不起火、不爆炸;溫度<150℃。 |
7.2過充電 | 充飽電后的電池,用3C電流和4.8V的恒定電壓充電8小時。 | 電池應不起火、不爆炸;溫度<150℃。 |
7.3 過放電 Over Discharge | 標準充電后,電池芯以 0.2C恒電流放電至 2.0V,用一根內阻小于30? 的導線連接電池芯正負極 24 小時。 (After standard charge. Cells are discharged at constant Current of 0.2C to 2.0V, and the positive and negative terminal is connected by a 30? wire for 24 hours. Cell Condition: Fresh, Fully charged cell.) | 不爆炸、不起火 (No explosion, No fire) |
7.4熱沖擊 | 將電池充飽電后,放置于熱箱中, 溫度以(5℃±2℃)/min的速率升至130℃±2℃并保溫30min。 | 電池應不起火、不爆炸。 |
7.5 強制放電 (Forced Discharge) | 電池芯以0.2 C進行放電至 2.0V,然后以1.0C的電流對電池進行反向充電,要求充電時間不低于 90min。 (The cell shall be discharge to 2.0V with the current 0.2C, then the discharge cell is subjected to reverse charge at 1.0Cfor not less than 90minutes.) | 不爆炸、不起火 (No explosion, No fire) |
7.6 高溫儲存 (High Temperature Storage Test) | 將電池芯放置在 80±2℃自然對流烘箱中 7 小時后,取出待返回到室溫,目測電池芯要求:充滿電的新電池芯。 (Put cell into the 80℃ box and keep the cell in the box for 7 hours after it be charged according to 6.1, and then take it out. Cell Condition: Fresh, Fully charged cell.) | 不爆炸、不起火 (No explosion, No fire) |
7.7冷熱循環性 能測試 (Thermal-cold Cycling Performance Test) | 電池芯在標準充電后,在環境溫度 75±2℃條件下開路放置 6 小時,然后-40℃條件下開路放置 6 小時,溫度轉換時間小于 30 分鐘,溫度循環 10 次,最后室溫條件下放置 24h, 觀察電池芯外觀變化。 (The full-charged cell is placed in 75±2℃ for 6h, and then put the Cell in -40℃ for 6h; change temperature time <30min, then repeat it for 10 cycles. Finally the cell is placed in room temperature for 24h. Watch the appearance of cell.) | 不起火、不爆炸、不冒煙, 試驗后開 路電壓應不低于試驗前的90﹪,質 量損失≤0.1% (No explosion, No fire, No smoke, Open circuit voltage changed not less than 90%, mass loss limit: ≤0.1%) |
7.8 重物撞擊 (Impact Test) | 用一條直徑為 15.8±0.1mm 的圓棒放置在電池芯中央,將重量為 9.1±0.46Kg 的重錘從 610±25mm 的高度垂直落下在電池芯長度的中心位置。電池芯要求:充滿電的新電池芯。 (A test sample cell is to be placed on a flat surface. A 15.8±0.1mm diameter bar is to be placed across the center of the sample. A 9.1Kg±0.46Kg mass is to be dropped from the height of 610±25mm to the center of the cell vertically. Cell Condition: Fresh, Fully charged cell.) | 不爆炸、不起火 (No explosion, No fire) |